| Table of Contents | ||||||
|---|---|---|---|---|---|---|
|
Unpacking
Carefully unpack the PAX-S Shuffler from the box. Set any foam or packing material aside. Make sure all the included components and parts are present.
PAXS Shuffler
Power Cable
Software shipped Separately
Remove foam or packing material from the inside of the shuffler:
Remove the Top Cover
Remove the Sliding Pate by Pulling Upwards and Out.
Carefully Remove the Foam Packing from inside the Shuffler.
Reinstall Sliding plate.
Initial Set Up
Static Brush Kit
Now is a good time to install the Static Brush kit if your casino is using plastic cards. Theses should ship with the shuffler and be installed during setup.
PAX Static Brush Kit Installation
Install Micro SD Card
| Note |
|---|
Before Powering on the PAX-S Shuffler for the first time, the Micro SD Card with Regulated Software must be installed. |
With the shuffler display facing you:
Remove Left Side Cover
The Micro SD Card Slot is located on the Main PCB to the right of the Fan.
Insert the Micro SD Card with the connectors facing up.
The Card should snap into place.
You will reinstall the cover at after all setup is complete.
Base Machine Settings
The Time, Date and Serial Number will be set at the factory and retained on the SSD. However, the Time and Time Zone may need to be updated at the location.
With the shuffler powered on:
From the Main Menu, Select the Gear Icon to Enter the User Menu.
In the User Menu Select the Maintenance Button.
Enter the Password and Select the Enter Button.
We are not allowed to put the password in the document. Call support if you need a reminder.
In theMaintenanceMenu Select the Utilities Button.
From the Utilities Menu Select the Base Machine Settings Button.
Enter the : Serial Number, Time Zone, Time and Date and Select the Set Date and Time Button.
Select the Home Icon to Return the Main Menu.
Adjustments
The video below goes with the Insert and Output Adjustments.
Shuttle Insert Offset (Calibration)
Remove right side cover.
From the Main Menu, Select the Gear Icon to Enter the User Menu.
In the User Menu Select the Maintenance Button.
Enter the Password and Select the Enter Button.
We are not allowed to put the password in the document. Call support if you need a reminder.
Select Machine Control > Machine Calibration > Select Shuttle Insert Offset. Press the return key with the current value.
For reference 300 points equals 1 card thickness and 150 points half a card thickness. A higher number will lower the shuttle position.Adjust until alignment marks on side plate and shuttle line up.
Output setting
Watch the video above for how to set the output setting. Make sure to reinstall the Sliding Plate and press the home button to return to home screen.
Brake Roll Setting
The gap between the two aluminum brake rollers should be approximately 1 ½ card thicknesses. This gap should be checked during installation.
With the shuffler turned OFF:
Remove the Outfeed Tray
Remove the Infeed Tray
If adjustment is needed follow these steps:
Use a Hex 2.5mm t-handle to loosen the Screws attaching the Brake Roller Shaft.
Slide the .015mm Pink Shim (Included) between the two Black Brake Rollers.
Push down firmly (about 5 to 10 pounds of pressure) and evenly on the top roller and tighten the two 2.5mm Hex Screws.
Be Sure the Gap is even across both sets of rollers.
Replace the Infeed and Outfeed Trays.
Card Weight Belt Tension
Check the Card Weight Belt Tension. The belt should not be loose.
https://youtu.be/tXH_64TB2XU| Include Page | ||||
|---|---|---|---|---|
|
Add Deck
It is necessary to add a new deck to the Shuffler in order for the system to properly recognize the specific cards in use.
From the Main Menu, Select the Gear Icon to Enter the User Menu.
In the User Menu Select the Maintenance Button.
Enter the Password and Select the Enter Button.
In theMaintenanceMenu Select the Deck Setup Button.
From the Deck Setup Menu Select the Add New Deck button.
Enter a name for the deck and Select Enter.
It is best practice to use the card manufactures description for the deck name. For Example: Bee Jumbo where the manufacturer is Bee, and the deck type is Jumbo.
Note: The deck of cards will be processed through the shuffler in a specific order. Fist in one direction and then rotated 180° processed again.
Start with a deck of cards in order from bottom to top: Ace-King of Spades, Ace-King Diamonds, King-Ace of Clubs, King-Ace of Hearts, and finally the two jokers on the top.
When Prompted to Add New Deck, Place the Deck in the Infeed Tray.
The Shuffler will input the Deck.
Select Accept to accept the shuffle.
Remove the Deck from the Outfeed Tray, Rotate the Deck and Place the Deck back in the Infeed Tray.
Select Accept to accept the 2nd shuffle
Once the Deck Operation Successful message appears, Navigate Back to the User Menu.
Select the Current Deck button.
Find the New Deck in the list, Select it and Select Done.
Navigate back to the Deck Setup menu.
Select Maintenance > Maintenance Password > Deck Setup > Delete Deck
Select the Deck to be Deleted and Select the Delete Selection(s) button.
Select the Return button and repeat if necessary.
Delete all decks not used at the location.
Note: The active deck will not show on the list of decks to delete.
Game Setup
| Note |
|---|
DO NOT skip reading this note: You must have one game selected before exiting the menu. If you do not have a game selected and you exit, it will brick the SSD on the motherboard. Do not ask how we figured this out…. |
Most Stud poker games played in a casino are listed in the Games Selection menu. The user menu needs be configured to show only the games at the casino where Pax is installed. A check box next to each game in the game selection menu will show if the game is to appear in the user menu.
Select Gear Icon > Maintenance > Maintenance Password > Game Setup > Edit Game
Select the Game to be Configured.
To configure select Game Setup in the Maintenance Menu and edit each game. Select yes or no to display the game in the user menu.
Enable (default) or Disable the Dealer Cover Card / Green Button Press Options.
Note: Pax can be configured to hold the first packet of cards or automatically eject the first packet into the outfeed tray. Select enable Dealer Cover Card/Green Button Press to require a green button is press or a cut card placed on the outfeed tray to eject the first packet of cards. Select disable Dealer Cover Card/Green Button Press to automatically eject the first packet of cards after the cards have been shuffled.
Test Run
After setup is complete 10 test shuffles with a deck of cards in use at the location should be performed.
Table Mounting
Full table Cut
Bracket to join back bar on table ring
Most tables have the back bar attached to the padded ring not to the table top
Template to cut table with router and router guide
½ straight router bit and ¾ OD template guide
Partial Table Cut
Metal frame same size opening as full cut
Allows Pax to mount in an opening cut into the table but not as deep.
Attaches to table top
Same part for RH and LH
Bracket to join table ring
Same part use for a full cut install
Template to cut table with router
Account for extra width of metal frame
Off Table
Mount shuffler behind the table with no modifications to table or table ring
Wood block with opening for shuffler mounted on metal bracket.
1 ½ thick wood
¼ inch spacers between table and bracket to account for thicker tables
Support leg to prevent table from tipping
Account for high and low tables
Right and left hand versions
(PM) Preventative Maintenance
| Include Page | ||||
|---|---|---|---|---|
|
Tool Kit C40-00444
Description | AGS # |
Tool Kit w/everything below | C40-00444 |
Hex Driver 1.5mm | |
Hex Driver 2mm |
|
Hex Driver 2.5mm |
|
Hex Driver 3mm |
|
T-Handle Driver 2mm |
|
T-Handle Driver 2.5mm |
|
Additional Tools | AGS # |
Service Request Lables | C40-00418 |
Cleaning Cards | C40-00450 |
.015 Pink plastic Shim | C40-00415 |
Router Template Full Cut "Order as needed on install" | C40-00396 |
Router Template 1/2 Cut "Order as needed on install" | C40-00397 |
Bee Playing Cards Red | C40-00385 |
Bee Playing Cards Blue | C40-00386 |
Cloth ( bag of a few ) | C103413 |
Cotton Swab ( box of 100) | C22-00005 |
Trouble Shooting and Bulitens
| Include Page | ||||
|---|---|---|---|---|
|