Table of Contents | ||||||
---|---|---|---|---|---|---|
|
Unpacking
Carefully unpack the PAX-S Shuffler from the box. Set any foam or packing material aside. Make sure all the included components and parts are present.
PAXS Shuffler
Power Cable
Software shipped Separately
Remove foam or packing material from the inside of the shuffler:
Initial Set Up
Static Brush Kit
Now is a good time to install the Static Brush kit if your casino is using plastic cards. Theses should ship with the shuffler and be installed during setup.
PAX Static Brush Kit Installation
Install Micro SD Card
Note |
---|
Before Powering on the PAX-S Shuffler for the first time, the Micro SD Card with Regulated Software must be installed. |
Base Machine Settings
The Time, Date and Serial Number will be set at the factory and retained on the SSD. However, the Time and Time Zone may need to be updated at the location.
With the shuffler powered on:
From the Main Menu, Select the Gear Icon to Enter the User Menu.
In the User Menu Select the Maintenance Button.
Enter the Password and Select the Enter Button.
We are not allowed to put the password in the document. Call support if you need a reminder.
In theMaintenanceMenu Select the Utilities Button.
From the Utilities Menu Select the Base Machine Settings Button.
Enter:
Serial Number (input all the numbers after the S2),
Time Zone, Time and Date
toggle which side the button goes on. Ask the casino which side they want.
Select the Home Icon to Return the Main Menu.
Adjustments
The video below goes with the Insert and Output Adjustments.
Shuttle Insert Offset (Calibration)
Note |
---|
The shuffler must be powered off before removing the side cover, if it is not you will get a red light error and be unable to continue. |
Remove right side cover.
From the Main Menu, Select the Gear Icon to Enter the User Menu.
In the User Menu Select the Maintenance Button.
Enter the Password and Select the Enter Button.
We are not allowed to put the password in the document. Call support if you need a reminder.
Select Machine Control > Machine Calibration > Select Shuttle Insert Offset then press the return key with the current value.
For reference 300 points equals 1 card thickness and 150 points half a card thickness. A higher number will lower the shuttle position.Adjust until alignment marks on side plate and shuttle line up.
Output setting
Watch the video above for how to set the output setting. Make sure to reinstall the Sliding Plate and press the home button to return to home screen.
Brake Roll Setting
The gap between the two aluminum brake rollers should be approximately 1 ½ card thicknesses. This gap should be checked during installation.
With the shuffler turned OFF:
Remove the Outfeed Tray
Remove the Infeed Tray
If adjustment is needed follow these steps:
Use a Hex 2.5mm t-handle to loosen the Screws attaching the Brake Roller Shaft.
Slide the .015mm Pink Shim (Included) between the two Black Brake Rollers.
Push down firmly (about 5 to 10 pounds of pressure) and evenly on the top roller and tighten the two 2.5mm Hex Screws.
Be Sure the Gap is even across both sets of rollers.
Replace the Infeed and Outfeed Trays.
Card Weight Belt Tension
Check the Card Weight Belt Tension. The belt should not be loose.
https://youtu.be/tXH_64TB2XUInclude Page | ||||
---|---|---|---|---|
|
Add Deck
It is necessary to add a new deck to the Shuffler in order for the system to properly recognize the specific cards in use.
From the Main Menu, Select the Gear Icon to Enter the User Menu.
In the User Menu Select the Maintenance Button.
Enter the Password and Select the Enter Button.
In theMaintenanceMenu Select the Deck Setup Button.
From the Deck Setup Menu Select the Add New Deck button.
Enter a name for the deck and Select Enter.
It is best practice to use the card manufactures description for the deck name. For Example: Bee Jumbo where the manufacturer is Bee, and the deck type is Jumbo.
Note: The deck of cards will be processed through the shuffler in a specific order. Fist in one direction and then rotated 180° processed again.
Start with a deck of cards in order from bottom to top: Ace-King of Spades, Ace-King Diamonds, King-Ace of Clubs, King-Ace of Hearts, and finally the two jokers on the top.
[5/15 2:39 PM] James Schaefer
I can confirm your deck is sorted in the correct deck add order.
in general, the advice is to try deck add as many as half a dozen times in a row until it succeeds.When Prompted to Add New Deck, Place the Deck in the Infeed Tray.
The Shuffler will input the Deck.
Select Accept to accept the shuffle.
Remove the Deck from the Outfeed Tray, Rotate the Deck and Place the Deck back in the Infeed Tray.
Select Accept to accept the 2nd shuffle
Once the Deck Operation Successful message appears, Navigate Back to the User Menu.
Select the Current Deck button.
Find the New Deck in the list, Select it and Select Done.
Navigate back to the Deck Setup menu.
Select Maintenance > Maintenance Password > Deck Setup > Delete Deck
Select the Deck to be Deleted and Select the Delete Selection(s) button.
Select the Return button and repeat if necessary.
Delete all decks not used at the location.
Note: The active deck will not show on the list of decks to delete.
Game Setup
Note |
---|
DO NOT skip reading this note: You must have one game selected before exiting the menu. If you do not have a game selected and you exit, it will brick the SSD on the motherboard. Do not ask how we figured this out…. |
Most Stud poker games played in a casino are listed in the Games Selection menu. The user menu can needs be configured to show only the games at the casino where Pax is installed. A check box next to each game in the game selection menu will show if the game is to appear in the user menu.
Select Gear Icon > Maintenance > Maintenance Password > Game Setup > Edit Game
Select the Game to be Configured.
To configure select Game Setup in the Maintenance Menu and edit each game. Select yes or no to display the game in the user menu.
Enable (default) or Disable the Dealer Cover Card / Green Button Press Options.
Note: Pax can be configured to hold the first packet of cards or automatically eject the first packet into the outfeed tray. Select enable Dealer Cover Card/Green Button Press to require a green button is press or a cut card placed on the outfeed tray to eject the first packet of cards. Select disable Dealer Cover Card/Green Button Press to automatically eject the first packet of cards after the cards have been shuffled.
Test Run
After setup is complete 10 test shuffles with a deck of cards in use at the location should be performed.
Adjustments
Insert Offset
Remove right side cover.
Select Shuttle Insert Offset. Press the return key with the current value.
For reference 300 points equals 1 card thickness and 150 points half a card thickness. A higher number will lower the shuttle position.
Adjust until alignment marks on side plate and shuttle line up.
Break Roll Setting
The gap between the two aluminum brake rollers should be approximately 1 ½ card thicknesses. This gap is set at the factory and should not need to be reset during installation.
Note |
---|
Warning: Power Down and Unplug the Pax S Shuffler before swapping the Buttons. Failure to do so may result in Damage to the unit, Shock or Electrocution |
Remove the Right Side Cover
Remove the Infeed Tray
Use a Hex Driver to loosen the Screws attaching the Top Roller Shaft.
Slide the .015mm Pink Shim (Included) between the two Black Brake Rollers.
Push down firmly (about 5 to 10 pounds of pressure) and evenly on the top roller and tighten the 2 Hex Screws.
Be Sure the Gap is even across both sets of rollers.
Replace the Infeed Tray and Right Side Cover.
Table MountingTable Mounting
Full table Cut
Bracket to join back bar on table ring
Most tables have the back bar attached to the padded ring not to the table top
Template to cut table with router and router guide
½ straight router bit and ¾ OD template guide
Partial Table Cut
Metal frame same size opening as full cut
Allows Pax to mount in an opening cut into the table but not as deep.
Attaches to table top
Same part for RH and LH
Bracket to join table ring
Same part use for a full cut install
Template to cut table with router
Account for extra width of metal frame
Off Table
Mount shuffler behind the table with no modifications to table or table ring
Wood block with opening for shuffler mounted on metal bracket.
1 ½ thick wood
¼ inch spacers between table and bracket to account for thicker tables
Support leg to prevent table from tipping
Account for high and low tables
Right and left hand versions
(PM) Preventative Maintenance
Bi-Weekly PAX PM video below.
https://playags.atlassian.net/wiki/spaces/FKB/pages/15680077930/PAX+S#Service-Videos
C40–00450
Cleaning Cards "ORDER AS NEEDED FOR TECHS"
10
C40-00418
Service Request Lables " Leave at casino"
1
C103413
Cloth
Bag
C22-00005
Cotton Swab
Box of 100
Annually
KIT-80022
Pax Roller Kit "ORDER KITS AS NEEDED"
1 Kit Per Shuffler
Include Page | ||||
---|---|---|---|---|
|
Tool Kit C40-00444
Description | AGS # |
Tool Kit w/everything below | C40-00444 |
Hex Driver 1.5mm | |
Hex Driver 2mm |
|
Hex Driver 2.5mm |
|
Hex Driver 3mm |
|
T-Handle Driver 2mm |
|
T-Handle Driver 2.5mm |
|
Additional Tools | AGS # |
Service Request Lables | C40-00418 |
Cleaning Cards | C40-00450 |
.015 Pink plastic Shim | C40-00415 |
Router Template Full Cut "Order as needed on install" | C40-00396 |
Router Template 1/2 Cut "Order as needed on install" | C40-00397 |
Bee Playing Cards Red | C40-00385 |
Bee Playing Cards Blue | C40-00386 |
Cloth ( bag of a few ) | C103413 |
Cotton Swab ( box of 100) | C22-00005 |
Trouble Shooting
Problem
Cause
Solution
Shuffler will not initialize; cooling fan is running.
SD card with software not installed.
Install SD card on carrier board.
Display shows service mode when all covers are in place.
Missing magnet to activate sensor.
Locate missing magnet and reattach with epoxy.
Ejector stops in the extended position.
Belt clamp not aligned with motor pulley.
Belt tension is too tight.
Ejector caught on cards in shuttle
Loosen belt clamp, move belt to align with motor pulley and tighten camp.
Loosen belt tension.
In the Machine Control menu adjust offset to center ejector
Plastic cards causing jams and not stacking on outfeed.
Plastic cards create static electricity.
No path to ground for anti-static brush.
Install anti-static brush kit.
Check continuity from brush to ground on AC plug. Also check AC outlet for proper ground.
Not able to move cards to the staging position.
Incorrect pick-off roller clearance.
Infeed tray not low enough.
Update for infeed tray.
Cards slipping on rollers
Adjust clearance using .015 shim.
Adjust steel brackets for magnets to be positioned as far down as possible.
Replace with new infeed tray C40-00417.
Clean rollers
Will not retain time, date in Base Machine Settings
Dead battery on carrier PCB.
Replace 3V battery CR1220.
Display shows missing and unknown cards.
Incorrect card type selected in user menu.
Cards in use not added to user menu.
Select current card in user menu that matches cards in use.
In the maintenance menu add the deck that will be used.
Occasional unknown card.
Card not stopping completely at camera.
Tighten the pick-off belt.
Card not able to enter shuttle.
Insert offset not set or set incorrectly
Guide blocks misaligned
Bad Hall Effect sensor for shuttle homing
Loose shuttle belt tensioner
In the Machine Control menu adjust offset to align marks
Re-align guide blocks
Replace the bottom hall effect sensor for the shuttle
and
tighten shuttle belt tensionerEjector leaving cards behind or making scraping sound.
Eject offset not set or set incorrectly
Ejector bracket misaligned at an angle
In the Machine Control menu adjust offset to center ejector
Align ejector bracket to be horizontal
Display is off
Normal function
Tap the display to wake it up. We are not allow to let it stay on during the shuffle.
Tech Bulletins
PAX-S Shuttle Position Tech Bulletin
There is an issue when forming the community cards in the Pax S Shuffler. The errors will be aborting the shuffle or leaving one or more cards in the infeed while showing incorrect deck composition. This issue will be isolated to games with community cards and using paper cards.
An adjustment will be made to the gap in the card guides at the exit rollers. The shuttle insert calibration will need to set the shuttle at a higher position. All shufflers at the location should be updated so Pax can be moved to any game.
Setup and Adjustments
Use a clamp to hold the shuttle at the top when tightening the belt clamp and adjusting the card guides. Before making adjustments make sure the screws for the shuttle belt clamp are tight.
Use the white plastic .025” shim to set the clearance.Loosen these four screws.
Hold the top and bottom card guides together while keeping the shim centered in the calibration mark. Tighten the 4 screws.
Repeat the adjustment for the guide blocks on the other side.
In the Calibrate Shuttle screen line up the insert marks as shown.
Serial number S200106 and above Subtract 600 from the insert calibration and enter the new value. The calibration marks will look like this. A lower value will raise the shuttle position.
Serial numbers below S200106 subtract 400 from the insert calibration and enter the new value.
Pax Shufflers that had previously been working well subtract 200 from the insert calibration and enter the new value.
Starting with serial number S200147 the card guide and the insert calibration adjustments will be made in production.Bulletins
Child pages (Children Display) | ||
---|---|---|
|