Versions Compared

Old Version 35

changes.mady.by.user Emery Redenius

Saved on

compared with

New Version Current

changes.mady.by.user Emery Redenius

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.
Image Removed

Table of Contents
minLevel1
maxLevel7
outlinetrue

Unpacking

Carefully unpack the PAX-S Shuffler from the box. Set any foam or packing material aside. Make sure all the included components and parts are present.

 

PAXS Shuffler

Power Cable

Software shipped Separately

Remove foam or packing material from the inside of the shuffler:

  1. Remove the Top Cover

  2. Remove the Sliding Pate by Pulling Upwards and Out.

  3. Carefully Remove the Foam Packing from inside the Shuffler.

  4. Reinstall Sliding plate.

Initial Set Up

Static Brush Kit

Now is a good time to install the Static Brush kit if your casino is using plastic cards. Theses should ship with the shuffler and be installed during setup.

PAX Static Brush Kit Installation

Install Micro SD Card

Note

Before Powering on the PAX-S Shuffler for the first time, the Micro SD Card with Regulated Software must be installed.

With the shuffler display facing you:

  1. Remove Left Side Cover

  2. The Micro SD Card Slot is located on the Main PCB to the right of the Fan.

  3. Insert the Micro SD Card with the connectors facing up.

  4. The Card should snap into place.

  5. Replace the Left Side CoverYou will reinstall the cover at after all setup is complete.

Base Machine Settings

The Time, Date and Serial Number will be set at the factory and retained on the SSD.  However, the Time and Time Zone may need to be updated at the location.

 With the shuffler powered on:

  1. From the Main Menu, Select the Gear Icon to Enter the User Menu.

  2. In the User Menu Select the Maintenance Button.

  3. Enter the Password and Select the Enter Button.

    1. We are not allowed to put the password in the document. Call support if you need a reminder.

  4. In theMaintenanceMenu Select the Utilities Button.

  5. From the Utilities Menu Select the Base Machine Settings Button.

  6. Enter:

    1. Serial Number (input all the numbers after the S2),

    2. Time Zone, Time and Date

    and Select the Set Date and Time Button

    2. toggle which side the button goes on. Ask the casino which side they want.

  7. Select the Home Icon to Return the Main Menu.

Shuttle home position

  1. .

Adjustments

The video below goes with the Insert and Output Adjustments.

machine_calibration (720p).mp4

Shuttle Insert Offset

and Output Setting

(Calibration)

Note

The shuffler must be powered off before removing the side cover, if it is not you will get a red light error and be unable to continue.

  1. Remove right side cover.

  2. From the Main Menu, Select the Gear Icon to Enter the User Menu.

  3. In the User Menu Select the Maintenance Button.

  4. Enter the Password and Select the Enter Button.

    1. We are not allowed to put the password in the document. Call support if you need a reminder.

  5. Select Machine Control > Machine Calibration > Select Shuttle Insert Offset

. Press

  1. then press the return key with the current value. 
    For reference 300 points equals 1 card thickness and 150 points half a card thickness. A higher number will lower the shuttle position.

  2. Adjust until alignment marks on side plate and shuttle line up.

Break

Output setting

Watch the video above for how to set the output setting. Make sure to reinstall the Sliding Plate and press the home button to return to home screen.

Brake Roll Setting

The gap between the two aluminum brake rollers should be approximately 1 ½ card thicknesses. This gap is set at the factory and should not need to be reset checked during installation.

Note

Warning: Power Down and Unplug the Pax S Shuffler before swapping the Buttons. Failure to do so may result in Damage to the unit, Shock or Electrocution

  1. Remove the Right Side CoverWith the shuffler turned OFF:

  2. Remove the Outfeed Tray

  3. Remove the Infeed Tray

    IMG_7891.MOV

    If adjustment is needed follow these steps:
    Use a Hex

Driver

  1. 2.5mm t-handle to loosen the Screws attaching the

Top

  1. Brake Roller Shaft.

Image Removed
  1. Image Added

  1. Slide the .015mm Pink Shim (Included) between the two Black Brake Rollers.

  2. Push down firmly (about 5 to 10 pounds of pressure) and evenly on the top roller and tighten the two 2.5mm Hex Screws.

  3. Be Sure the Gap is even across both sets of rollers.

  4. Replace the Infeed Tray and Right Side CoverOutfeed Trays.

brake_roller_adjustment (720p).mp4

Card Weight Belt Tension

Check the Card Weight Belt Tension. The belt should not be loose.

https://youtu.be/tXH_64TB2XU
Include Page
PAX Card Weight Belt Tension
PAX Card Weight Belt Tension

Add Deck

It is necessary to add a new deck to the Shuffler in order for the system to properly recognize the specific cards in use.

  1. From the Main Menu, Select the Gear Icon to Enter the User Menu.

  2. In the User Menu Select the Maintenance Button.

  3. Enter the Password and Select the Enter Button.

  4. In theMaintenanceMenu Select the Deck Setup Button.

  5. From the Deck Setup Menu Select the Add New Deck button. 

  6. Enter a name for the deck and Select Enter.

It is best practice to use the card manufactures description for the deck name. For Example: Bee Jumbo where the manufacturer is Bee, and the deck type is Jumbo.

 Note: The deck of cards will be processed through the shuffler in a specific order. Fist in one direction and then rotated 180° processed again.

Start with a deck of cards in order from bottom to top: Ace-King of Spades, Ace-King Diamonds, King-Ace of Clubs, King-Ace of Hearts, and finally the two jokers on the top.

[5/15 2:39 PM] James Schaefer

I can confirm your deck is sorted in the correct deck add order.  

    in general, the advice is to try deck add as many as half a dozen times in a row until it succeeds.  

    1. When Prompted to Add New Deck, Place the Deck in the Infeed Tray.

    2. The Shuffler will input the Deck.

    3. Select Accept to accept the shuffle.

    4. Remove the Deck from the Outfeed Tray, Rotate the Deck and Place the Deck back in the Infeed Tray.

    5. Select Accept to accept the 2nd shuffle

    6. Once the Deck Operation Successful message appears, Navigate Back to the User Menu.

    7. Select the Current Deck button.

    8. Find the New Deck in the list, Select it and Select Done.

    9. Navigate back to the Deck Setup menu.

    10. Select Maintenance > Maintenance Password > Deck Setup > Delete Deck

    11. Select the Deck to be Deleted and Select the Delete Selection(s) button.

    12. Select the Return button and repeat if necessary.

    13. Delete all decks not used at the location.

    14. Note: The active deck will not show on the list of decks to delete.

    Game Setup

    Note

    DO NOT skip reading this note: You must have one game selected before exiting the menu. If you do not have a game selected and you exit, it will brick the SSD on the motherboard. Do not ask how we figured this out….

    Most Stud poker games played in a casino are listed in the Games Selection menu. The user menu can needs be configured to show only the games at the casino where Pax is installed. A check box next to each game in the game selection menu will show if the game is to appear in the user menu.

     

    Select Gear Icon > Maintenance > Maintenance Password > Game Setup > Edit Game

    1. Select the Game to be Configured.

      1. To configure select Game Setup in the Maintenance Menu and edit each game. Select yes or no to display the game in the user menu.

    2. Enable (default) or Disable the Dealer Cover Card / Green Button Press Options.

     

    Note: Pax can be configured to hold the first packet of cards or automatically eject the first packet into the outfeed tray. Select enable Dealer Cover Card/Green Button Press to require a green button is press or a cut card placed on the outfeed tray to eject the first packet of cards. Select disable Dealer Cover Card/Green Button Press to automatically eject the first packet of cards after the cards have been shuffled.

    Test Run

    After setup is complete 10 test shuffles with a deck of cards in use at the location should be performed.

    Table Mounting

    https://youtu.be/4Fo2Pn9-_gA

    Full table Cut

    • Bracket to join back bar on table ring

      • Most tables have the back bar attached to the padded ring not to the table top

    • Template to cut table with router and router guide

      • ½ straight router bit and ¾ OD template guide

    Partial Table Cut

    • Metal frame same size opening as full cut

      • Allows Pax to mount in an opening cut into the table but not as deep.

      • Attaches to table top

      • Same part for RH and LH

    • Bracket to join table ring

      • Same part use for a full cut install

    • Template to cut table with router

      • Account for extra width of metal frame

    Off Table

    Mount shuffler behind the table with no modifications to table or table ring

    • Wood block with opening for shuffler mounted on metal bracket.

      • 1 ½ thick wood

    • ¼ inch spacers between table and bracket to account for thicker tables

    • Support leg to prevent table from tipping

      • Account for high and low tables

    • Right and left hand versions

    (PM) Preventative Maintenance

    Include Page
    PAX Preventative Maintenance.
    PAX Preventative Maintenance.

    Tool Kit C40-00444

    Description

    AGS #

    Tool Kit w/everything below

    C40-00444

    Hex Driver 1.5mm

    Hex Driver 2mm

     

    Hex Driver 2.5mm

     

    Hex Driver 3mm

     

    T-Handle Driver 2mm

     

    T-Handle Driver 2.5mm

     

    Additional Tools

    AGS #

    Service Request Lables

    C40-00418

    Cleaning Cards

    C40-00450

    .015 Pink plastic Shim

    C40-00415

    Router Template Full Cut  "Order as needed on install"

    C40-00396

    Router Template 1/2 Cut "Order as needed on install"

    C40-00397

    Bee Playing Cards Red

    C40-00385

    Bee Playing Cards Blue

    C40-00386

    Cloth ( bag of a few )

    C103413

    Cotton Swab ( box of 100)

    C22-00005

    Trouble Shooting

    Include PageTrouble Shooting PAXTrouble Shooting PAXTech

    and Bulletins

    Include Pagechildren
    PAXs Tech Bulletins
    PAXs Tech BulletinsallChildrentrue